\documentclass[a4paper,12pt]{article}

\usepackage[a4paper, total={180mm, 272mm}]{geometry}

\usepackage{fontspec}

\setmainfont[Path=fonts/, Extension=.ttf]{ipaexm}

\setlength\parindent{3.5em}

\setlength\parskip{0em}

\renewcommand{\baselinestretch}{1.247}

\begin{document}

\thispagestyle{empty}

\Large

\noindent \\

Motion Blur Ino\medskip

\par

\normalsize

Produces a linear motion blur effect by using translation values.\par

It is also possible to specify an afterimage shake effect in the options.\\

\par

When \textquotedbl Alpha Rendering\textquotedbl \ is ON, Alpha channel will be processed first,\par

then it will process all RGB pixels where the Alpha channel is not zero.\\

\par

When \textquotedbl Alpha Rendering\textquotedbl \ is OFF, Alpha channel will not be taken into account,\par

so the RGB image changes will not be masked, causing defined edges.\\

\\

-{-}- \ Inputs \ -{-}-\\

Source\par

Connect the image to be processed.\\

\\

-{-}- \ Settings \ -{-}-\\

Depend Move\par

\noindent \ \ \, P1 -> P2\par

Use the X1,Y1,X2,Y2 parameters to specify movement in a fixed direction and\par 

magnitude.\\

\par

\noindent \ \ \, Motion\par

It will take into account the object movements along the X and Y channels,\par 

on a frame-by-frame basis.\par

The X1,Y1,X2,Y2 parameters values will be ignored.\\

\\

X1\\

Y1\\

X2\\

Y2\par

Specifies the start and end coordinate values for the motion blur.\par

The origin of the used coordinate system is at the lower left corner.\par

The unit is millimeters.\par

By specifying values with decimal places, it will be possible to define subtle changes\par 

in the length.\par

If the distance between the starting and ending points is less than 1/16 of a pixel,\par 

it will have no effect.\par

The default values are\par

\noindent \hskip 7em X1 Y1 -> 0.0 0.0\par

\noindent \hskip 7em X2 Y2 -> 1.0 1.0\par

\newpage

\thispagestyle{empty}

\ \vspace{-0.2em}

\par

\noindent Scale\par

Adjusts the scale for the length of the motion blur effect.\par

For example,\par

\noindent \hskip 7em X1 Y1 -> 0.0 0.0\par

\noindent \hskip 7em X2 Y2 -> 1.0 -1.0\par

\noindent \hskip 7em Scale -> 100\par

Would be equivalent to,\par

\noindent \hskip 7em X1 Y1 -> 0.0 0.0\par

\noindent \hskip 7em X2 Y2 -> 100.0 -100.0\par

and will have the same effect.\par

When Scale is 0, blur will not be applied.\par

The default value is 1, which will apply no scaling.\\

\\

Curve\par

Allows to adjust the blur strenght.\par

With a value between 1.0 and 10.0, blur will become stronger.\par

With a value between 0.1 and 1.0, blur will become lighter.\par

The default value is 1, which will produce an linear attenuation.\\

\\

Afterimage Length\par

Specify the lenght of the afterimage effect.\par

The unit is millimeters.\par

Specify a value greater than or equal to 0.\par

For example, to create an afterimage for a line with a width of 3,\par

specify a value greater than or equal to 3.\par

The default value is 0, which produces no afterimage.\\

\\

Afterimage Power\par

Determines the strength of the afterimage.\par

At 0, no afterimage effect will be applied.\par

The larger the value, the less blur and stronger afterimage effect will be applied.\par

The default value of 1 is the strongest possible one. Where there will be no\par 

motion blur, but only the afterimage effect applied.\\

\\

Alpha Rendering\par

This option is valid only when there is an Alpha channel.\par

When inactive, it masks the changes in the RGB values using the original Alpha\par 

of the image.\par

When active, the effect will be able to modify the Alpha channel, extending it\par 

as necessary to reproduce the full span of the effect.\par

The default setting is active.

\end{document}